south parlor wainscoting

Wall Painting Tips

Want to paint like a pro? Here are a few recommendations. From appropriately preparing surface areas to selecting the right tools and Colours, these keys will help you to achieve a flawless finish. Discover how to create a smooth finish, and exactly how to deal with common blunders like touches and drips. Discover the very best methods to cut in around trim and edges, and how to create sharp, clean lines. With these expert ideas, you’ll be able to paint like a pro and save money and time on your next painting project.

Many Painters like to add paint extenders to help the paint flow better and go further. We do NOT recommend that with Old Village Paint. You’ll find Old Village goes on like butter and lasts longer than any modern day paint. If you’d like to thin it to make it go further we recommend Distilled water for our water based paints and clear Mineral Spirits for our Oil Base paints. 

Scratch a Ridge along the Edge in Textured Ceilings

The problem with painting walls along the edge of textured ceilings is that it’s practically impossible to obtain a straight line along the top of the wall surface without getting paint on the ceiling bumps. Pros have a simple solution. They run a screwdriver along the perimeter of the ceiling to scrape off the structure. This allows you to cut in without getting paint on the ceiling. The screwdriver produces a small ridge in the ceiling, so the paint bristles naturally enter into it.

Make use of the blue painter’s tape as opposed to concealing tape. Masking tape can leave behind a sticky residue that’s difficult to clean off. And also, paint can cause masking tape to distort, which allows paint run underneath it. Painter’s tape can be left on for days (some up to 2 weeks) and still peel off cleanly. And it stops paint from bleeding without distorting.

Scrape Tape with Putty Knife

For a seamless painting experience, it’s important to prevent paint from bleeding under the tape. A seasoned painter suggests an easy yet reliable technique: use tape over the wood and then use a putty blade to press down the tape, developing a tight seal. This technique guarantees that paint will not leak, saving you the hassle of scrape removal.

The only time you’ll want to use white primer is under white or bright yellow paint. Otherwise we recommend gray primer. Gray Primer does a far better job of covering the existing paint colour than simple primer, so your finish coat will be extra vibrant and may require 2 coats. Old Village paints are so heavily pigmented that it not always an issue. We recommend using primer over surfaces that haven’t ever been painted or when you’ll need to scrape old surfaces to the base. In this case, usually spot priming is adequate.

Start With a Brush full of paint 

Pros take a “fill brush and go” technique to painting. They fill the bottom 1 1/2 inches of their brush with paint, slap each side within the bucket to rip off the hefty drips, and begin painting. By contrast, house owners frequently take a “dip and strip” strategy of dragging the packed brush alongside their container and wiping off a lot of the paint. It does not do you good to dip your brush in paint, then immediately scrape it back into the bucket. You’ll cover a lot more wall with a full brush.

Make certain to review the tag and follow directions– this stuff is powerful. Rubber gloves and eye protection are needed.

Push Paint to Stay Clear Of Runs

When your brush is packed with paint, it’s simple to develop runs by applying excessive paint in edges or along trim. To prevent that, begin 1/2 inch away from the cut-in location. As the brush discharges, move over and slowly drag the brush along the trim or corner. Let the bristles carefully push the paint against the cut-in area where the wall surfaces meet. You may have to do this a couple of times to get total protection, however it’ll avoid excess paint along woodwork and in edges.

Rather than taping the home windows, scratch them when paint sashes. Taping takes a lot of time and paint frequently ends up on glass anyway. Enabling paint to get on the glass is all right because it can be easily gotten rid of with a razor blade once it is completely dry. It only takes a few secs for the paint to peel. 

Use what the pros use — canvas ground cloth. They’re not slippery and they soak up splatters (you’ll still want to clean up huge spills as they can bleed through). “Unless you’re painting a ceiling, you do not need a jumbo-size canvas that fills the whole area,” a pro says. “A canvas fabric that’s just a few feet wide and runs the size of the wall surface is suitable for safeguarding your floor, and it’s easy to relocate.”

Professionals in the paint sector prevent making use of bed sheets as ground cloth, and you need to follow their lead. The reason is that bed sheets are too slim to efficiently prevent paint splatters and spills from seeping thru. In addition, while plastic ground cloth can consist of spills, they tend to maintain the paint damp for an extensive period, which can lead to the paint transferring to the soles of your shoes and being tracked throughout your home. Canvas ground cloth, on the other hand, provide a better solution for protecting your floor.

Complete One Wall Surface Prior To Starting Another

It might seem easy to do all the edges and trim in a room, after that go back to roll the wall surfaces, BUT DON’T. Pros get a seamless appearance by cutting in one wall, after that promptly rolling it before beginning the following. This allows the cleaned and the rolled paint to mix together much better.

Wash Unclean Wall Surfaces With Degreaser

Repaint will not bond to greasy surfaces, like cooking area wall surfaces above a stove or any dirty surface. Use a degreaser to clean dingy or oily surface areas and rinse with warm water for better paint adhesion.

Box Paint for Constant Shade

The “exact same” color of paint can range ever so slightly from batch to batch. That difference can be noticeable if you use 2 different batches on one wall. To ensure color consistency throughout, it’s best to mix different batches of paint together in a 5 gallon pail, (a process called “boxing”).

When transitioning in between brushing and rolling, secure your paint container, tray, or bucket by covering it with a damp towel to avoid your paint and tools from drying during durations of non-use. If stopping for the night we have Brush and roller covers that will allow you to not wash them out until painting the next day or washing them out later. You’ll want to fill the brush or roller with paint to help it stay wet. /product-category/paint-brushes

Prior to using your roller covers for the first time, it’s a good idea to give it a fast wash with warm water and a drop of dish soap. This helps remove any type of unwanted fibers that might come off during painting, leaving them smoother and extra reliable. To do this, just run your hands backwards and forwards the covers, scrubbing gently to remove any loosened fibers. This procedure is called “preconditioning covers.” When you’ve done this, you can start utilizing the roller covers immediately with water based paint – there’s no need to await them to completely dry.

Join Our Mailing List

Have Something to Contribute?